Contact Us
TEL: +86-755-29799869
E-mail:marketing@zdfcard.cn
Address: 5F, A Bldg., Hongwei Industrial Park, 70th area, Bao'an, Shenzhen, China
Home > Knowledge > Content
FM1204 chip non-contact CPU card parameters and manufacturing process
Mar 31, 2018

FM1204 chip CPU card is a non-contact CPU card chip produced by Fudan Microelectronics. The product supports ISO/IEC14443-A protocol and is compatible with M1 card. The CPU instruction is compatible with the general 8051 instruction, built-in hardware DES coprocessor, and the data memory is EEPROM of 5Kbyte (4K for CPU card, 1K for M1 card). The FM1204 is a non-contact CPU card that meets the bank's standards. COS also supports the PBOC 2.0 standard and the IC card application specification of the Ministry of Construction.

【 Technical Parameters 】

Protocol Standard: ISO/IEC 14443-A

Compatible with FM11RF08, M1 card

MCU instructions are compatible with 8051

Working frequency: 13.56Mhz

Data transmission rate: 106Kbit/S

Program Memory: 32KX8bitROM

Data storage: 5K

256X8bitiRAM

384x8bit RAM

Number of rewritable: >100 thousand times

Data storage: >10 years


【safety】

The security mechanism of FM1204M01 is:

1. Anti-power analysis module

2. There is a high and low frequency detection reset module, the chip operating frequency is automatically reset beyond the detection range

3. ROM anti-reverse extraction, memory data encryption

 【printing art】

1, code: membership card can play flat code, spray code, small convex code, large convex code, laser code, bar code and so on. Size embossing can be hot or hot silver. Note: The commonly used membership card embossed codes are played on the side of the card. If you want to use the embossed code on the short side of the card, you must make a charge according to the personalized code. (There is a certain limitation on the slot width of the automatic embossing machine. The vertical embossing code cannot pass through the machine.) The flat code can be a flat code or a flat code. The flat code is black, gold and silver. Laser code is common orange; bar code can be spray bar code, can be bar code, high quality bar code generally do UV bar code.


2. If silk screen gold or silk screen silver is required, special instructions are required. If there is no special description, direct color printing will be used when printing.


3. The thickness of the membership card: If not specified, the card is made to the default standard thickness (0.76mm).


4, because each printing is a certain color, if there is a sample card, will be subject to sample card, printing as close to the color of the sample card, but it is not possible to reach 100%. If the requirements for color are very strict and the number of cards is relatively large, digital proofing or printing proofing should be used to confirm the printing effect (out of sample card) when the goods are allowed. A quantity of 20,000 sheets or less is generally a small quantity of single imposition, and a color difference of less than 15% is considered normal.


5. The color effect of the last printing on the member card will have certain differences with the color effect seen on the computer monitor. Even if the same design document is viewed on different monitors, the effect will be different (for example, in the LCD monitor (LCD). ) Looks different from what you see on a normal display (CRT). There are also a few color differences between cards printed in the same design manuscript in batches.


6, when doing membership card design, the line thickness can not be less than 0.076, otherwise the printed lines can not see clearly.


7. The distance from the convex code to the edge of the card should be at least 4-5mm; the distance from the magnetic stripe to the edge should be 4mm, and the width of the ordinary magnetic stripe should be 12.7mm. When placing a single order, it must be specified whether it is a high magnetic stripe or a low magnetic stripe. Write magnetic data requirements.


7. The size of each small character is approximately 3mm, and the size of each large character is approximately 4mm.


8, order documents as much as possible into the CDR format, text, symbols, patterns, please turn into a curve.